manualshive.com logo in svg

Furuno FCV-38, Manual

Share
Download
Furuno FCV-38 Manual Download Page 23

1.  OPERATION

1-11

1

1.4

How to Change Display Modes

The FCV-38 has five base screens, split beam, multi-beam, zoom, external sounder-
high frequency, and external sounder-low frequency. By combining screens you can 
see underwater objects from a wide variety of viewpoints. For how to combine 
screens, see section 4.7.8.

1.4.1

How to change the display mode for the FCV-38

Note: 

To change the display mode on the external fish finder window, see 

section 1.21.1.

1. If the header is not displayed, put the cursor at the top edge of the display to show 

it.

[Advanced Settings] menu.
Accesses the advanced settings menu, change various settings for the 
FCV-38 and undo/redo actions.
[Internal Settings] menu.
Saves/Loads data to/from the Processor Unit’s internal memory. See 
section 1.28.

[External Settings] menu.
Saves/Loads data to/from an external memory device. See section 1.28.

[Advanced Settings] icon.
Accesses the [Advanced Settings] pop-up menu.
See section 1.5 and chapter 4.
[Undo] icon.
"Undo" the last operation. See section 1.29.

[Redo] icon.
"Redo" the last operation. See section 1.29.

[Select External Memory Device] icon.
Accesses the external memory device which saves screenshots. See 
section 3.3.

Note: 

Appears only when an external memory device is connected.

Icon

Description/Options

Menu

Item

[Save Settings] icon: Saves current settings to media set to 
the Processor Unit.*
[Load Settings] icon: Loads settings from the media set to the 
Processor Unit.

*Eight sets of settings (                    )

 

 

 

 

 

 

 

 

 

  

~

[Save External Unit Settings] icon: Saves current settings to
an external memory device.

[Load External Unit Settings] icon: Loads settings from an
external memory device.

Summary of Contents for FCV-38

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands