manualshive.com logo in svg

Furuno FCV-38, Manual

Share
Download
Furuno FCV-38 Manual Download Page 13

1-1

1

1.

OPERATION

1.1

Trackball Control Unit

Item

Function, description

Power button ( )

Press to turn the power on or off.

Power indicator

Lights green when the power is on.

Trackball

Moves the cursor.

Left button

Click

: Selects the item highlighted with the cursor.

Double click

: Output Target Latitude and Longitude (TLL).

Long push

: Moves the selected window, marker line, etc.

Right button

Short push

: Shows/hides the InstantAccess bar

™

.

Long push

: Starts the scroll back mode. Confirms picture when the 

scroll back mode is active.

Scrollwheel

Scroll

: Changes the setting for the selected item.

Short push

: Takes a screenshot (still image).

Long push

: Replays screenshots.

USB port cover

Open to access the USB port, where a USB flash memory can be in-
serted. When the USB port is not in use, cover the USB port with the 
port cover.

Note: 

Do not use this port to connect external memory devices for data 

recording or saving screenshots.

Scrollwheel

USB port cover

Right button

Left button

Power indicator

Power button

Trackball

Summary of Contents for FCV-38

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands