manualshive.com logo in svg

Furuno FCV-38, Manual

Share
Download
Furuno FCV-38 Manual Download Page 38

1.  OPERATION

1-26

1.13

Zoom Modes

The zoom modes (displays) expand the specified area of the split beam display. Four 
modes are available: bottom lock, bottom zoom, marker zoom and bottom discrimina-
tion. The default mode is bottom lock.

Note: 

A window which contains a zoomed screen can be shown (see section 4.7.8). 

You can freely change the size of the window by dragging and dropping the window 
frame. The display position can be moved by dragging and dropping the window.

Zoom window (example: bottom lock)

To select a zoom mode, do the following:

1. Select the [Sounder] icon (

) from the InstantAccess bar™ to show the [Sound-

er] menu.

2. Select the [Zoom] mode icon (

). [ZOOM MODE] appears in the miscellaneous 

section of the header.

3. Scroll to show the desired zoom mode. The four modes are shown in abbrevia-

tions.

•  BL: Bottom Lock
•  BZ: Bottom Zoom

•  MZ: Marker Zoom
•  BD: Bottom Discrimination

• On (green)

䠖

 Display size and position can be changed.

• Off

䠖

Only display size can be changed.

㻌

[ZOOM MODE] indication

Summary of Contents for FCV-38

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands