Fujitsu SPARC Enterprise T5440 Server User Manual Download Page 12

Page: 12 / 92

SPARC Enterprise T5440 Server Product Notes • December 2010

Important New Information About the
SPARC Enterprise T5440 Server

This section describes new capabilities that are supported on the SPARC Enterprise
T5440 server.

■

For information about the capabilities that have been supported at the release of the
previous edition, see the following sections.

■

“RAID Function” on page 22

■

“Support for SSD Storage” on page 24

RFID Tag

RFID tags are attached to the servers shipped after August 2010 in stages. Note that
the servers with and without the RFID tag may temporarily exist.

FIGURE 1-1

shows the location of the RFID tag.

FIGURE 1-1

SPARC Enterprise T5440 Server Appearance (Front View)

FIGURE 1-2

shows the appearance of RFID tag.

RFID Tag

Summary of Contents for SPARC Enterprise T5440 Server





























































































Search results

Summary of Contents for SPARC Enterprise T5440 Server

Reviews:

Related manuals for SPARC Enterprise T5440 Server

Brands by name

Popular brands

Fujitsu SPARC Enterprise T5440 Server, User Manual

Search results

Summary of Contents for SPARC Enterprise T5440 Server

Reviews:

Related manuals for SPARC Enterprise T5440 Server

Brands by name

Popular brands