Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 172 / 280

5-28

C122-B001-02EN

CHAPTER 5 Business LAN Management by GSWB

VLAN Tag of mirroring frame

This section explains the VLAN Tag of the mirroring frame.

Figure 5.11 VLAN Tag of mirroring frame

Monitored port: Port B transmission/reception

Mirror port: Port C

Frames are transferred between ports A and B.

Ports A and B belong to the same VLAN (VLAN 10).

Port B is set so that it sends frames without a VLAN Tag.

(VLAN 10 is set as native in access or trunk mode.)

• Transfer from port A to port B

The following explains how the frame tag is handled when a frame is transferred from
port A to port B.

Table 5.17 VLAN Tag of mirroring frame (transfer from port A to port B)

A frame without a tag is sent from the monitored port (port B) but a frame with
a tag is mirrored to the mirror port (port C).

• Transfer from port B to port A

The following explains how the frame tag is handled when a frame is transferred from
port B to port A.

Port A

Port B

Port C

Receiving a frame without a tag

Sending a frame without
a tag

Frame without a tag

Receiving a frame with a VLAN 10
tag

Sending a frame without
a tag

Frame with a VLAN 10 tag (*1)

Port A

VLAN 10

Port B

Port C

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands