manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, System Design Manual

Share
Download
Fujitsu PRIMEQUEST 440 System Design Manual Download Page 199

C122-B001-02EN

7-1

 

CHAPTER 7  Hot Swapping

1

This chapter describes hot swapping of hardware components.

Hot swapping is implemented for the purpose of replacing a component that was 
operating but stopped due to a failure during system operation, with a normal 
component, without stopping the entire server operation.  The component that had 
been swapped can be incorporated into the running system again.  In this chapter, hot 
swapping also refers to deleting or adding a component without stopping the entire 
server, such as deliberately deleting a component from system operation, adding a 
component for expansion purposes, as well as replacing a component that was 
operating but stopped due to a failure.

In principle, hot swapping should be implemented by a Fujitsu certified service 
engineer.

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands