manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, System Design Manual

Share
Download
Fujitsu PRIMEQUEST 440 System Design Manual Download Page 144

4-38

C122-B001-02EN

CHAPTER 4 Hardware System Management

 

4.3.9

Operation management software linkage

This function enables a linkage with operation management software.

Figure 4.27

 shows software that is installed on a partition and that can work with the 

PSA.

The function enables the PSA to work with operation management software such as 
Systemwalker.  It uses SNMP (Simple Network Management Protocol) for the 
linkage.

Figure 4.27  Operation management software linkage

For the REMCS

System administrator

Management LAN

PRIMEQUEST

SNMP

Operation management software console

Reference

PSA

Linux/Windows

MMB-FW

SNMPD

SNMPD

Log information

Operation management software

MIB

MIB

PSA

Linux/Windows

MMB-FW

SNMPD

SNMPD

Log information

Operation management software

MIB

MIB

MMB

Partition#n

MMB

Partition#n

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands