Fujitsu AGHG09KVCA Manual Download

Page: 131 / 403



Parts

Exterior

Part name

Model name

Summary

Remote sensor

unit

UTY-XSZX

Thermo-sensor for sensing the
temperature of arbitrary place in the
room.

Auto louver

grille kit

UTD-GXTA-W

Width: 683 mm
For 07, 09, 12, and 14 models

Air cleaning filter

UTR-FA16-5

Air cleaning filter can be mounted to
the indoor unit.

External

connect kit

UTY-XWZX

Use to connect with various peripheral
devices and air conditioner PCB.

External

connect kit

UTY-XWZXZ5

Required when external device is
connected.

External

connect kit

UTY-XWZXZG

Use to connect with various peripheral
devices and air conditioner PCB.
For control output port.

Air outlet shutter

plate

UTR-YDZB

Installed at the air outlet when 3-
directions mode is performed.

Fresh-air intake

kit

UTZ-VXAA

By attaching Fresh-air intake kit to the
indoor unit, it can be taken in fresh air
of up to 10% of “high” air volume of
the indoor unit.

Insulation

kit

Insulation for

high humidity

UTZ-KXGC

Install when the under-roof condition is
expected to be the humidity of over
80% and the temperature of over
30 °C.

Half concealed

kit

UTR-STA

Used for the indoor unit installing of
half concealed.

Communication

kit

UTY-TWBXF2

Use to connect with optional devices
and air conditioner PCB.

6-1. Indoor unit

- (02-87) -

6. Optional parts

TECHNICAL DATA

AND PARTS LIST

TECHNICAL DATA

AND PARTS LIST

Summary of Contents for AGHG09KVCA




















































































































































































































































































































































































































Search results

Summary of Contents for AGHG09KVCA

Reviews:

Related manuals for AGHG09KVCA

Brands by name

Popular brands

Fujitsu AGHG09KVCA, Manual

Search results

Summary of Contents for AGHG09KVCA

Reviews:

Related manuals for AGHG09KVCA

Brands by name

Popular brands