Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 42 | Manualshive

Page: 42 / 56

Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 42

8

Cleaning

DANGER!
Mains voltage!
– Before beginning with cleaning work, disconnect

the mains plug and protect the device against being

unintentionally switched back on!

– Do not allow any liquids to flow into the device.
– Indicate cleaning work with warning signs.
– Put safety equipment back into operation after

cleaning work.

8.1 Grinding chamber

NOTICE!
Hold the crushing jaw firmly! The part weighs approx.

6.5 kg.

To access the crushing chamber, it is first necessary to completely disas-

semble the fixed crushing jaw.
To do so, open the front cover. Position the guide pin horizontally to

unlatch it.
Pull out the guide pin and remove the crushing jaw. (See

Chapter 6.3.1

‘Assembling the crushing plates’ on page 29).
Clean the crushing chamber with a vacuum cleaner and brush or blow it

out with compressed air, if necessary. (Attention: projected grinding

stock)
Harder residues of sample material on the crushing plates can be

removed with a wire brush. Afterwards, wipe out the crushing chamber

with alcohol (corrosion protection).

Cleaning

- 42 -

«
...
40
41
42
43
44
...
»

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments