manualshive.com logo in svg

Fritsch PULVERISETTE 1 classic line, Operating Instructions Manual, Page: 27 / 56

Share
Download
Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 27

Model I

Material

Designation

Order number

Movable crushing plate

43.0110.27

1 pair of support walls

43.0160.27

Manganese steel

Fixed crushing plate

43.0130.23

Movable crushing plate

43.0140.23

Aluminium

1 pair of support walls

43.0150.13

Model II

Material

Designation

Order number

Hardened tool steel

Fixed crushing plate

43.3010.09

Movable crushing plate

43.3020.09

1 pair of support walls

43.3070.09

Chromium-free steel

Fixed crushing plate

43.3011.09

Movable crushing plate

43.3021.09

1 pair of support walls

43.3071.09

Chromium-nickel stainless steel

Fixed crushing plate

43.3030.10

Movable crushing plate

43.3040.10

1 pair of support walls

43.3080.10

Tungsten carbide (WC + Co)

Fixed crushing plate

43.3050.08

Movable crushing plate

43.3060.08

1 pair of support walls

43.3090.08

Zirconium oxide

Fixed crushing plate

43.3100.27

Movable crushing plate

43.3110.27

1 pair of support walls

43.3160.27

Manganese steel

Fixed crushing plate

43.3130.23

Movable crushing plate

43.3140.23

Aluminium

1 pair of support walls

43.3150.13

The crushing plates made of zirconium oxide are only suitable for

crushing medium-hard and brittle materials (or similar). Metal may not

be crushed under any circumstances.
The Cr-Ni steel equipment is recommended for crushing damp material;

this would cause the plates and walls made of tool steel to rust.

 

Using the device

 

 

- 27 -

 

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments