manualshive.com logo in svg

Fritsch PULVERISETTE 1 classic line, Operating Instructions Manual, Page: 7 / 56

Share
Download
Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 7

2 

Safety information and use

2.1  Requirements for the user

This operating manual is intended for persons assigned with operating

and monitoring the Fritsch of the PULVERISETTE 1 classic line. The oper-

ating manual and especially its safety instructions are to be observed by

all persons working on or with this device. In addition, the applicable

rules and regulations for accident prevention at the installation site are

to be observed. Always keep the operating manual at the installation site

of the of the PULVERISETTE 1 classic line.
People with health problems or under the influence of medication,

drugs, alcohol or exhaustion must not operate this device.
The of the PULVERISETTE 1 classic line may only be operated by author-

ised persons and serviced or repaired by trained specialists. All commis-

sioning, maintenance and repair work may only be carried out by techni-

cally qualified personnel. Qualified personnel are persons who, because

of their education, experience and training as well as their knowledge of

relevant standards, regulations, accident prevention guidelines and oper-

ating conditions, are authorised by those responsible for the safety of the

machine to carry out the required work and are able to recognize and

avoid possible hazards as defined for skilled workers in IEC 364.
In order to prevent hazards to users, follow the instructions in this

manual.
Malfunctions that impair the safety of persons, the of the PULVERISETTE

1 classic line or other material property must be rectified immediately.

The following information serves both the personal safety of operating

personnel as well as the safety of the products described and any devices

connected to them: All maintenance and repair work may only be per-

formed by technically qualified personnel.
This operating manual is not a complete technical description. Only the

details required for operation and maintaining usability are described.
Fritsch has prepared and reviewed this operating manual with the

greatest care. However, no guarantee is made for its completeness or

accuracy.
Subject to technical modifications.

 

Safety information and use

 

 

- 7 -

 

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments