Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 22 | Manualshive

Page: 22 / 56

Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 22

5

Initial start-up

CAUTION!
Crushing hazard!
Only operate the Laboratory - jaw crusher with the

funnel attached!

Switch on the device only after all work as described in

‘Installation’ on page 17 has been carried out.
During the first hours of operation, a small quantity of grease may escape

from the cam bearing of the movable crushing jaw (see

‘Lubricating the bearings’ on page 45). After a few hours of operation,

the grease will be evenly distributed throughout the roller bearing com-

partment and grease will no longer escape.

NOTICE!
Only operate the Laboratory - jaw crusher with the

crushing plates installed and fastened!

5.1 Switching on

Set the main switch to ON (I). The jaw crusher starts up.

5.2 Switching off

Set the main switch to OFF (0). The Laboratory - jaw crusher stops within

a few seconds.

Initial start-up

- 22 -

«
...
20
21
22
23
24
...
»

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments