manualshive.com logo in svg

Fritsch PULVERISETTE 1 classic line, Operating Instructions Manual, Page: 32 / 56

Share
Download
Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 32

1.

First, lift out the fixed crushing jaw as described in 

Ä

 Chapter 6.3.1

‘Assembling the crushing plates’ on page 29.

2.

Unscrew and remove the exterior belt guard (see 

Ä

 Further infor-

mation on page 30).

3.

Take off the used V-belt by slowly rolling it over the belt disc.

4.

Pull the flywheel off its axis with 2 persons.

CAUTION!
Crushing hazard!
When removing the support walls, be careful not to

drop them. Before removing the last fastening screw,

the support wall has to be firmly held on the inside.

5.

Remove the 6 visible fastening screws of the left support wall and

lift it out from the interior.

6.

The 6 fastening screws of the right support wall are directly acces-

sible from the exterior. Unscrew the screws and lift out the support

wall from the interior.

7.

To install the support walls, follow the same steps in reverse order.

During installation, make sure the support walls are positioned cor-

rectly because the pairs are not identical. The fastening screws

have to be firmly screwed on.
After the flywheel has been screwed on, put the V-belt back on.
The belt guard has to be attached again.

CAUTION!
Risk of injury!
The belt guard has to be attached to the device

before starting up each time.

 

Using the device

 

 

- 32 -

 

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments