manualshive.com logo in svg

Fritsch PULVERISETTE 1 classic line, Operating Instructions Manual, Page: 26 / 56

Share
Download
Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 26

3.

Raise of lower the pressure plate into one of the two possible posi-

tions and push the bolt through the pressure plate.

NOTICE!
Make sure that the bolt is pushed through the

pressure plate and that it is not above or below

the pressure plate. This can cause damage to the

device.

4.

Turn the bolt so that it cannot slide out due to vibrations.

5.

Mount the cover back on the exhaust.

6.2  Selecting the crushing plates and lateral support walls

The standard model of the Laboratory - jaw crusher is equipped with

crushing plates and support walls made of hardened tool steel.
In custom-built or retrofitted models, crushing jaws and support walls

are available which are made of the following materials:

Model I

Material

Designation

Order number

Hardened tool steel

Fixed crushing plate

43.0010.09

Movable crushing plate

43.0020.09

1 pair of support walls

43.0070.09

Chromium-free steel

Fixed crushing plate

43.0011.09

Movable crushing plate

43.0021.09

1 pair of support walls

43.0071.09

Chromium-nickel stainless steel

Fixed crushing plate

43.0030.10

Movable crushing plate

43.0040.10

1 pair of support walls

43.0080.10

Tungsten carbide (WC + Co)

Fixed crushing plate

43.0050.08

Movable crushing plate

43.0060.08

1 pair of support walls

43.0090.08

Zirconium oxide

Fixed crushing plate

43.0100.27

 

Using the device

 

 

- 26 -

 

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments