Foma F905I, Manual

Page: 384 / 532

382
PC connection setting
Data Communication
Communications between FOMA terminal and a
connected PC are classified to packet communication and
64K data communication.
･
To make packet or 64K data communications or edit
data such as the phonebook using a PC connected,
installation of the software in the attached CD-ROM and
various settings are required.
･
DoCoMo does not guarantee operations on upgraded
OS.
･
For packet communication overseas, use IP connection
(packet communication is disabled with PPP
connection). 64K data communication may be disabled
for some networks you use.
･
FOMA terminal does not support fax communication or
Remote Wakeup.
･
Data communication can be performed connecting
with PDA of DoCoMo, musea, sigmarion II or sigmarion
III. Note that update of musea or sigmarion II is required
for use. For details of such as method to update, refer
to the DoCoMo website.
❖
Packet communication
Packet communication charges are based on the amount
of data sent and received, which makes it suitable for
high-speed exchange of comparatively small amounts of
data as in sending and receiving mail. No communication
charges are required when no data are exchanged even if
you are connected to the network. Therefore, sending/
receiving data as needed while remaining connected to
the network is possible.
High-speed packet communication can be performed at a
reception speed of up to 3.6 Mbps and a transmission
speed of up to 384 Kbps by using access points that
support FOMA packet communication such as mopera U
or mopera of DoCoMo's Internet connection service. The
actual transmission speed varies with the environment
and the rate of congestion.
Note that communications of large-size data such as
viewing websites containing images and downloading
require high charges.
* When connecting to an access point out of the FOMA high-
speed area or when you are using a device not compatible with
HIGH-SPEED such as mopera, or when using devices not
compatible with HIGH-SPEED such as DoCoMo's PDA, musea,
sigmarion II or sigmarion III, the connection is made at the
speed of 384 Kbps.for both reception and transmission.
❖
64K data communication
Since communication charges are based on the duration
of the connection to the network regardless of the volume
of data, it is suitable for sending and receiving relatively
large amounts of data as in downloading multi-media
contents.
Data can be sent/received at stabled communication
speed of 64 Kbps by using access points that support
FOMA 64K data communication services such as mopera
U or mopera of DoCoMo's Internet connection service or
ISDN synchronized 64K access points.
Be careful that a high cost is charged for long-time
communications.
Before use
◆ Operating environment
The operation environment for using data
communication is as shown below :
* This is the operating environment of FOMA PC configuration
software. Memory requirements and hard disk capacity may vary
by the PC system configurations.
･
Utilization may not be possible in certain operating
environments. Operation is not guaranteed in an
environment except that described above nor DoCoMo
assumes responsibility for pertaining to operation
under such conditions.
◆ Devices required
The devices below are required in addition to FOMA
terminal and PC :
- FOMA USB Cable with Charge Function 01(optional) or FOMA
USB Cable (optional)
- Attached CD-ROM "FOMA

F905i
用
CD-ROM (CD-ROM for
FOMA

F905i)"
* USB cable for PC is not available because the connector type is
different.
* If you use USB HUB, operations may not be performed
correctly.
* This manual uses examples using FOMA USB Cable with
Charge Function 01 for explanation.
Item Requirements
Computer PC/AT compatible computer with a
USB port (conform to USB
specification 1.1/2.0)
OS (Japanese version) Windows 2000, Windows XP,
Windows Vista
Memory
requirements
*
Windows 2000 : 64MB or more
Windows XP : 128MB or more
Windows Vista : 512MB or more
Hard disk capacity
*
5MB or more free disk space