manualshive.com logo in svg

Fischer Panda 45i pms, User Manual

Share
Download
Fischer Panda 45i pms User Manual Download Page 10

Seite/Page 10        Kapitel/Chapter 1:  

8.10.14

Leere Seite / Intentionally blank

10.8.2

Generator Specification  .................................................................................................. ..  169

10.8.3

PMGi out ......................................................................................................................... ... 170

10.9 PMGi protections ............................................................................................................................  .. 175

10.9.1

Short circuit ..................................................................................................................... ..  175

Panda iControl2............................................................................................................................................ ... 177

Current revision status ................................................................................................................................ ... 178

Hardware ....................................................................................................................................................... ... 178

1 Safety instructions for the Panda iControl2 ......................................................................................... ... 179

1.1

Personnel........................................................................................................................................  .. 179

1.2

Safety instructions...........................................................................................................................  .. 179

2 General operation ................................................................................................................................... ... 181

2.1

The Panda iControl2 panel .............................................................................................................  .. 181

2.2

Starting preparation / Checks (daily)...............................................................................................  .. 182
2.2.1

Marine version  ................................................................................................................ ..  182

2.2.2

Vehicle version  ............................................................................................................... ..  182

2.3

Operation ........................................................................................................................................  .. 183
2.3.1

Switching the controller on and off .................................................................................. ..  183

2.3.2

The default display screen .............................................................................................. ..  183

2.3.3

Operating modes  ............................................................................................................ ..  184
2.3.3.1

Stand-by mode ................................................................................................. ..  184

2.3.3.2

Start-up mode................................................................................................... ..  185

2.3.3.3

Override mode.................................................................................................. ..  186

2.3.3.4

Operation mode................................................................................................ ..  186

2.3.3.5

Stop mode ........................................................................................................ ... 189

2.3.3.6

Autostart mode ................................................................................................. ..  189

2.4

Other operating functions ............................................................................................................... ... 191
2.4.1

Set-up menu  ................................................................................................................... ..  191

2.4.2

Setting the brightness of the backlight ("backlight" and "dimtime")  ................................ ... 192

2.4.3

The configuration menu ("config")  .................................................................................. ..  193

2.4.4

The network ID  ............................................................................................................... ..  193

2.4.5

Saving settings and exiting the set-up menu ("Save & Exit")  ......................................... ..  193

2.4.6

Activating/deactivating the autostart function ("Autostart")  ............................................. ..  193

2.4.7

Resetting the service interval ("Service") ........................................................................ ..  195

2.4.8

Priming the fuel system ("Prime Fuel")  ........................................................................... ..  196

2.4.9

Selecting and saving a unit for the temperature value output ......................................... ..  196

3 Installation ............................................................................................................................................... ... 197

3.1

Personnel........................................................................................................................................  .. 197
3.1.1

Hazard warnings for installation ...................................................................................... ..  197

3.2

Disposal of the components............................................................................................................  .. 198
3.2.1

Panda iControl2 panel with installation housing  ............................................................. ..  199

3.2.2

Terminal assignments on the Panda iControl2 panel  ..................................................... ..  199

3.3

Dimensions .....................................................................................................................................  .. 200

3.4

Wiring of the Panda iControl2 controller .........................................................................................  .. 201
3.4.1

Terminal assignments on the Panda iControl2 controller  ............................................... ..  202
3.4.1.1

Terminal assignment of 18-pin connector ........................................................ ..  202

3.4.1.2

Fischer Panda standard bus ............................................................................ ..  202

3.4.1.3

Fischer Panda CAN bus................................................................................... ..  202

3.5

Start-up ...........................................................................................................................................  .. 203

Summary of Contents for 45i pms





















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands