manualshive.com logo in svg

Fischer Panda 45i pms, User Manual

Share
Download
Fischer Panda 45i pms User Manual Download Page 125

Maintenance Instructions

8.10.14

Kapitel/Chapter 7: Maintenance Instructions   -   Seite/Page 125

Fig. 7.16-5: Injection nozzles

Removing the nozzle heat shield ring seal within the scope of 
the maintenance work.

IMPORTANT!

•  Use a phillips screwdriver (1) with a diameter greater than 

the hole in the heat ring seal (approx. 6 mm (1/4 in)).

1. Lightly turn the screwdriver (1) into the hole in the heat 

ring seal.

2. Rotate the screwdriver three to four times in each direc-

tion.

3. When rotating the screwdriver, slowly extract the heat ring 

seal (4) together with the injection nozzle gasket (3).

4. If the heat ring seal drops back in, repeat the procedure 

above.

For assembly:

•  If the injection nozzle is uninstalled for cleaning or maintenance purposes, the heat seal ring and the injection nozzle 

gasket must be replaced.

(1) Phillips screwdriver (2) Injection nozzle
(3) Injection nozzle gasket (4) Heat ring seal

Summary of Contents for 45i pms





















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands