Fischer Panda 45i pms User Manual Download Page 7

Page: 7 / 212

8.10.14

Inhalt/Contens Seite/Page 7

Inhalt / Contens

Stopping the generator - see remote control panel data sheet....................................................... .... 56

6 Installation Instructions ......................................................................................................................... ..... 57

6.1

Personal requirements.................................................................................................................... .... 57
6.1.1

Hazard notes for the installation ..................................................................................... .... 57

6.2

Place of installation......................................................................................................................... .... 59
6.2.1

Preliminary remark ......................................................................................................... .... 59

6.2.2

Preparing the base - placement ..................................................................................... .... 59

6.2.3

Advice for optimal sound insulation ................................................................................ .... 60

6.3

Generator connections ................................................................................................................... .... 60

6.4

Installation of the cooling system - raw water ................................................................................. .... 61
6.4.1

General information ........................................................................................................ .... 61

6.4.2

Fischer Panda installation kit - raw water ....................................................................... .... 61

6.4.3

Installation of the through hull fitting in Yachts - scheme ............................................... .... 63

6.4.4

Quality of the raw water sucking in line .......................................................................... .... 63

6.4.5

Generator installation above waterline ........................................................................... .... 63

6.4.6

Raw water installation scheme ....................................................................................... ..... 65

6.4.7

Generator installation below waterline ............................................................................ .... 66

6.4.8

Generator Housing cooled by raw water ........................................................................ .... 66

6.4.9

Indirect cooling of the genset housing (by the heat exchanger) ..................................... .... 67

6.5

Installation of the cooling system - fresh water............................................................................... .... 68
6.5.1

Position of the external cooling water expansion tank .................................................... .... 68

6.5.2

Scheme for freshwater circuit at two circuit cooling system ........................................... ..... 69

6.6

installation...................................................................................................................................... .... 69

6.7

Installation of the water cooled exhaust system ............................................................................ ..... 70
6.7.1

Fischer Panda installation kit - Exhaust System ............................................................. .... 70

6.7.2

Installation of the standard exhaust system ................................................................... .... 71

6.8

.Installation of the waterlock ........................................................................................................... .... 72
6.8.1

Possible cause for water in the exhaust hose ................................................................ .... 73
6.8.1.1

Possible cause: exhaust hose.......................................................................... .... 73

6.8.1.2

Possible cause: cooling water hose ................................................................. .... 73

6.8.2

Installation area of the waterlock .................................................................................... .... 73

6.8.3

The volume of the waterlock ........................................................................................... .... 74
6.8.3.1

Ideal position of the waterlock.......................................................................... ..... 76

6.8.3.2

Example of the installation of the waterlock off-center and possible effects: ... ..... 79

6.9

Exhaust / water separator............................................................................................................... .... 82
6.9.1

Installation exhaust water separator ............................................................................... ..... 84

6.10 Fuel system installation .................................................................................................................. .... 84

6.10.1

Fischer Panda installation kit - Fuel system ................................................................... .... 84
6.10.1.1 The following items need to be installed: ......................................................... .... 86

6.10.2

Connection of the fuel lines at the tank .......................................................................... .... 89

6.10.3

Position of the pre-filter with water separator ................................................................. ..... 90

6.11 Generator DC system installation ................................................................................................... .... 90

6.11.1

Connection of the starter battery block ........................................................................... .... 90

6.11.2

How to connect two 12V batteries to a 24V battery bank ............................................... .... 94

6.11.3

Connection of the remote control panel - See Panda iControl panel manual ................. .... 95

6.12 Generator AC system installation ................................................................................................... .... 95

6.12.1

Installation PMGi inverter - See separate PMGi inverter manual ................................... .... 96

7 Maintenance Instructions....................................................................................................................... ..... 97

Summary of Contents for 45i pms





















































































































































































































Search results

Summary of Contents for 45i pms

Reviews:

Brands by name

Popular brands

Fischer Panda 45i pms, User Manual

Search results

Summary of Contents for 45i pms

Reviews:

Brands by name

Popular brands