manualshive.com logo in svg

Fischer Panda 45i pms, User Manual

Share
Download
Fischer Panda 45i pms User Manual Download Page 181

General operation

8.10.14

Kapitel/Chapter 2: General operation   -   Seite/Page 181

2. General operation

2.1

The Panda iControl2 panel 

The "Panda iControl2 panel" control panel is the control and display unit for the Panda iControl2 control system and
represents the interface between the user and the Panda iControl2 controller. The integrated display serves to
present the most important data of the system as well as warnings and error messages. 

The control panel is equipped with four buttons for operating the Panda iControl2 controller:

Fig. 2.1-1: Panda iControl 2 panel

1.

On/Off button:

 Switching the Panda iControl2 controller on and off

2.

Start/Stop button:

 Starting and stopping the generator, confirming values in selection menus (Enter key)

3.

Cursor-up button

 Switching between display screens (up), counting values up in selection menus

4.

Cursor-down button

 Switching between display screens (down), counting values down in selection menus.

Summary of Contents for 45i pms





















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands