Fischer Panda 45i pms User Manual Download Page 16

Page: 16 / 212

General Instructions and Regulations

Seite/Page 16 - Kaptitel/Chapter 1: General Instructions and Regulations

8.10.14

WARNING: Explosion hazard

Warning of substances that may cause an explosion under
certain conditions, e.g. presence of heat or ignition sources.

WARNING: Hot surface

Warning of hot surfaces and liquids. Burn/scalding hazard.

WARNING: Danger due to corrosive substances,
potential contamination of person

Warning of substances that cause chemical burns upon
contact. These substances can act as contaminants if
introduced into the body.

WARNING: System may be pressurised!

When the system is opened, the pressure can be relieved
abruptly and expel hot gases and fluids. Risk of injury due to
parts flying about, burn hazard due to liquids and gases.

WARNING: Hearing damage

Warning of hearing damages.

WARNING: Magnetic field

Warning of magnetic field.

WARNING: Overpressure

Warning of overpressure.

Summary of Contents for 45i pms





















































































































































































































Search results

Summary of Contents for 45i pms

Reviews:

Brands by name

Popular brands

Fischer Panda 45i pms, User Manual

Search results

Summary of Contents for 45i pms

Reviews:

Brands by name

Popular brands