Fiat 2013 500 ABARTH Owner'S Manual Download Page 71 | Manualshive

Page: 71 / 413

background image

4. Attach the lower hooks or connectors of the child

restraint to the lower anchorages in the selected seat-
ing position.

5. If the child restraint has a tether strap, connect it to the

top tether anchorage. See the section “Installing Child
Restraints Using the Top Tether Anchorage” for direc-
tions to attach a tether anchor.

6. Tighten all of the straps as you push the child restraint

rearward and downward into the seat. Remove slack
in the straps according to the child restraint manufac-
turer’s instructions.

7. Test that the child restraint is installed tightly by

pulling back and forth on the child seat at the belt
path. It should not move more than 1 inch (25.4 mm)
in any direction.

How To Stow An Unused ALR Seatbelt

When using the LATCH attaching system to install a
child restraint, stow all ALR seat belts that are not being
used by other occupants or being used to secure child
restraints. An unused belt could injure a child if they play
with it and accidentally lock the seatbelt retractor. Before
installing a child restraint using the LATCH system,
buckle the seat belt behind the child restraint and out of
the child’s reach. If the buckled seat belt interferes with
the child restraint installation, instead of buckling it
behind the child restraint, route the seat belt through the
child restraint belt path and then buckle it. Do not lock
the seatbelt. Remind all children in the vehicle that the
seat belts are not toys and that they should not play with
them.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

69

«
...
69
70
71
72
73
...
»

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2013 500 ABARTH

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: VanEssa mobilcamping Pages: 8

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Toyota Pages: 371

Carpower CAP-20

Brand: Monacor Pages: 2

Brand: StowAway 2 Pages: 2

Brand: SCC Pages: 4

Brand: Toyota Pages: 636

Brand: E&G Classics Pages: 4

Brand: APS Pages: 3

Brand: GReddy Pages: 12

Brand: FORM FIT Pages: 2

Brand: Brodit Pages: 2

Brand: Jaeger Pages: 14

Brand: TATA Motors Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands