Fiat 2013 500 ABARTH Owner'S Manual Download Page 376

Page: 376 / 413

Rear Tail, Stop, Backup And Turn Signal Lamps

1. Open the liftgate.

2. Remove the two screws and remove the tail lamp

assembly.

3. Remove the four screws (using a T20 driver) and

separate the backplate from the lamp housing.

4. Remove the tail, stop, or turn signal bulbs by pushing

them slightly and turning counter-clockwise.

5. Remove the backup lamp bulb by pulling straight out.

6. Replace lamps as required and reinstall lamp.

Center High Mounted Stop Lamp (CHMSL)

1. Remove the two guard caps and the two fastening

screws.

2. Remove the center high mounted stop lamp assembly.

3. Disconnect the electric connector.

4. Press the retaining device and open the bulb holder.

5. Remove the snap-fitted bulb to be replaced and re-

place it.

6. Close the back cap locking it properly.

7. Reinstall the two fastening screws and reinstall the

guard caps.

374

MAINTAINING YOUR VEHICLE

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands

Fiat 2013 500 ABARTH, Owner'S Manual

Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands