Fiat 2013 500 ABARTH Owner'S Manual Download Page 359 | Manualshive

Page: 359 / 413

background image

CAUTION!

Using a transmission fluid other than the manufac-
turer’s recommended fluid may cause deterioration
in transmission shift quality and/or torque converter
shudder. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for fluid speci-
fications.

Special Additives

The manufacturer strongly recommends against using
any special additives in the transmission.

Automatic Transmission Fluid (ATF) is an engineered
product and its performance may be impaired by supple-
mental additives. Therefore, do not add any fluid addi-
tives to the transmission. The only exception to this
policy is the use of special dyes for diagnosing fluid

leaks. Avoid using transmission sealers as they may
adversely affect seals.

CAUTION!

Do not use chemical flushes in your transmission as
the chemicals can damage your transmission compo-
nents. Such damage is not covered by the New
Vehicle Limited Warranty.

Fluid Level Check

The fluid level is preset at the factory and does not
require adjustment under normal operating conditions.
Routine fluid level checks are not required, therefore the
transmission has no dipstick. Your authorized studio can
check your transmission fluid level using special service
tools. If you notice fluid leakage or transmission malfunc-
tion, visit your authorized studio immediately to have

7

MAINTAINING YOUR VEHICLE

357

«
...
357
358
359
360
361
...
»

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2013 500 ABARTH

Brand: Camcar Pages: 2

Brand: Cargo Floor Pages: 16

Brand: Whispbar Pages: 15

Brand: Buick Pages: 428

Brand: AC Schnitzer Pages: 16

Brand: Ford Pages: 368

Brand: Cadillac Pages: 407

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Jaeger Pages: 14

Brand: Magneti Marelli Pages: 9

Brand: Cadillac Pages: 438

Brand: Car-Interface Pages: 25

Brand: Chevrolet Pages: 324

Brand: Westin Pages: 2

FreshSesh PowderHound

Brand: Yakima Pages: 18

Brand: FEATHERLITE TRAILERS Pages: 60

403.NISS4HT 2.36 RSR

Brand: Directed Pages: 22

Brand: DV8 Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands