Fiat 2013 500 ABARTH Owner'S Manual Download Page 173

Page: 173 / 413

To set the required language, proceed as follows:

1. Briefly press the

SET ESC

button. The previously set

“language” will flash on the display.

2. Press the UP

or DOWN

button for setting.

3. Briefly press the

SET ESC

button to go back to the

menu screen, or press and hold the

SET ESC

button

(approximately one second) to go back to the main
screen without storing the settings.

Buzzer Volume (Adjusting The Failure/Warning
Buzzer Volume)

With this function the volume of the buzzer accompany-
ing any failure/warning indication can be adjusted to
one of eight volume levels.

To adjust the volume proceed as follows:

1. Briefly press the

SET ESC

button. The previously set

volume “level” will flash on the display.

2. Press the UP

or DOWN

button for setting.

3. Briefly press the

SET ESC

button to go back to the

menu screen, or press and hold the

SET ESC

button

(approximately one second) to go back to the main
screen without storing the settings.

Button Volume (Button Volume Adjustment)

This function may be used to adjust the volume of the
beep accompanying the buttons.

SET ESC

, UP

DOWN

buttons can be adjusted according to 8 levels.

To adjust the volume, proceed as follows:

1. Briefly press the

SET ESC

button. The previously set

volume “level” will flash on the display.

2. Press the UP

or DOWN

button for setting.

UNDERSTANDING YOUR INSTRUMENT PANEL

171

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands

Fiat 2013 500 ABARTH, Owner'S Manual

Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands