manualshive.com logo in svg

Fiat 2013 500 ABARTH, Owner'S Manual

The Fiat 2013 500 ABARTH Owner's Manual is a comprehensive guide designed to help you understand and maximize your vehicle's performance. This manual is available for free download at manualshive.com, providing easy access to all the essential information needed to fully utilize your Fiat 500 ABARTH's features and capabilities.

Share
Download
background image

INSTRUMENT CLUSTER DESCRIPTIONS

1. Glow Plug Light — If Equipped

This vehicle will inhibit engine cranking when the
ambient temperature is less than –22° F (–30° C)

and the oil temperature sensor reading indicates an
engine block heater has not been used. The Glow Plug
light will flash during in cold weather for up to 10
seconds. An externally powered electric engine block
heater is available as optional equipment or from your
authorized studio).

The message

⬙

Plug In Engine Heater

⬙

, will be displayed

in the instrument cluster when the ambient temperature
is below 5°F (-15°C) at the time the engine is shut off as
a reminder to avoid possible crank delays at the next cold
start.

2. Rear Defrost Button

Press and release this button to turn on the rear
window defroster. This indicator will illuminate

when the rear window defroster is on. The rear window
defroster automatically turns off after 20 minutes.

CAUTION!

Failure to follow these cautions can cause damage to
the heating elements:

•

Use care when washing the inside of the rear
window. Do not use abrasive window cleaners on
the interior surface of the window. Use a soft cloth
and a mild washing solution, wiping parallel to the
heating elements. Labels can be peeled off after
soaking with warm water.

(Continued)

144

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2013 500 ABARTH

Wallbox Commander 2 Installation And User Manual preview
Commander 2
Brand: Wallbox Pages: 7
NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Brand: NavLinkz Pages: 4
Cequent 10417 Instruction Sheets preview
10417
Brand: Cequent Pages: 9
FormFit HD 23A 07 Installation Instructions preview
HD 23A 07
Brand: FormFit Pages: 4
muth signal mirror Instalation Instructions preview
signal mirror
Brand: muth Pages: 10
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Brand: BrandMotion Pages: 2
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Brand: Jeep Pages: 136
M7 SPEED AGS-R2 Manual preview
AGS-R2
Brand: M7 SPEED Pages: 6
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Brand: FVC Pages: 8
POOL-LINE 110050 Assembly Instructions preview
110050
Brand: POOL-LINE Pages: 2
BMW 84 61 0 028 926 Installation Instructions Manual preview
84 61 0 028 926
Brand: BMW Pages: 13
Roadtrek SS Agile 2017 Owner'S Manual preview
SS Agile 2017
Brand: Roadtrek Pages: 61
Westin 32-2250 Instructions preview
32-2250
Brand: Westin Pages: 3
BrandMotion 212IFD001N User Manual preview
212IFD001N
Brand: BrandMotion Pages: 12
Airstream 2008 Safari Owner'S Manual preview
2008 Safari
Brand: Airstream Pages: 103
Cadillac 2000 Escalade Manual preview
2000 Escalade
Brand: Cadillac Pages: 339
Rola RCLSH Fitting Instructions preview
RCLSH
Brand: Rola Pages: 2
Buick 2004 Rainier Getting To Know Manual preview
2004 Rainier
Brand: Buick Pages: 20

Brands by name

Popular brands

Load more brands