Fiat 2013 500 ABARTH Owner'S Manual Download Page 346

Page: 346 / 413

NOTE:

The rear wiper arm cannot be raised fully up-

ward unless the pivot cap is raised first.

2. Lift the rear wiper arm upward to raise the wiper

blade off of the liftgate glass.

3. Grab the bottom of the wiper blade and rotate it

forward to unsnap the blade pivot pin from the wiper
blade holder.

4. Install the wiper blade pivot pin into the wiper blade

holder at the end of the wiper arm, and firmly press
the wiper blade until it snaps into place.

1 — Wiper Blade
2 — Blade Pivot Pin
3 — Wiper Arm
4 — Wiper Blade Holder

344

MAINTAINING YOUR VEHICLE

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands

Fiat 2013 500 ABARTH, Owner'S Manual

Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands