Fiat 2013 500 ABARTH Owner'S Manual Download Page 311

Page: 311 / 413

NOTE:

Refer to the “Compact Spare Tire” section of the

“Tires-General Information” under “Starting And Oper-
ating” for information about the spare tire, it’s use, and
operation.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.

1. Remove the scissors jack and tool bag from under the

driver’s seat.

2. Loosen, but do not remove, the wheel bolts by turning

them to the left one turn while the wheel is still on the
ground.

NOTE:

There are front and rear jacking locations on each

side of the body (as indicated by the triangular lift point
symbol on the sill molding).

Jack Warning Label

Front Jacking Location

WHAT TO DO IN EMERGENCIES

309

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands

Fiat 2013 500 ABARTH, Owner'S Manual

Search results

Summary of Contents for 2013 500 ABARTH

Reviews:

Related manuals for 2013 500 ABARTH

Brands by name

Popular brands