manualshive.com logo in svg

Fiat 2013 500 ABARTH, Owner'S Manual

The Fiat 2013 500 ABARTH Owner's Manual is a comprehensive guide designed to help you understand and maximize your vehicle's performance. This manual is available for free download at manualshive.com, providing easy access to all the essential information needed to fully utilize your Fiat 500 ABARTH's features and capabilities.

Share
Download
background image

driven for up to 20 minutes above 15 mph (24 km/h) in
order for the TPMS to receive this information.

For example, your vehicle may have a recommended
cold (parked for more than three hours) tire pressure of
30 psi (207 kPa). If the ambient temperature is 68° F (20°
C) and the measured tire pressure is 27 psi (186 kPa), a
temperature drop to 20° F (-7° C) will decrease the tire
pressure to approximately 23 psi (159 kPa). This tire
pressure is sufficiently low enough to turn on the Tire
Pressure Monitoring Telltale Light. Driving the vehicle
may cause the tire pressure to rise to approximately 27
psi (186 kPa), but the Tire Pressure Monitoring Telltale
Light will still be on. In this situation, the Tire Pressure
Monitoring Telltale Light will turn off only after the tires
are inflated to the vehicle’s recommended cold tire pres-
sure value.

CAUTION!

•

The TPMS has been optimized for the original
equipment tires and wheels. TPMS pressures and
warnings have been established for the tire size
equipped on your vehicle. Undesirable system op-
eration or sensor damage may result when using
replacement equipment that is not of the same size,
type, and/or style. Aftermarket wheels can cause
sensor damage. Do not use aftermarket tire sealants
or balance beads if your vehicle is equipped with a
TPMS, as damage to the sensors may result.

•

After inspecting or adjusting the tire pressure,
always reinstall the valve stem cap. This will
prevent moisture and dirt from entering the valve
stem, which could damage the Tire Pressure Moni-
toring Sensor.

276

STARTING AND OPERATING

Summary of Contents for 2013 500 ABARTH






























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2013 500 ABARTH

Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
Ultra Start KE-6 Owner'S Manual preview
KE-6
Brand: Ultra Start Pages: 8
Warrior Winches C10000NH Assembly & Operating Instructions preview
C10000NH
Brand: Warrior Winches Pages: 17
Kia CADENZA 2019 Features & Functions Manual preview
CADENZA 2019
Brand: Kia Pages: 54
Metra Electronics 99-9001 Installation Instructions preview
99-9001
Brand: Metra Electronics Pages: 2
Hama 00178266 Operating Instruction preview
00178266
Brand: Hama Pages: 75
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
Webasto CC4E Installation And Service Instructions Manual preview
CC4E
Brand: Webasto Pages: 34
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Brand: Cadillac Pages: 34
Quadratec 12057.0261 Installation Manual preview
12057.0261
Brand: Quadratec Pages: 12
Quadratec 16053.5300 Installation Manual preview
16053.5300
Brand: Quadratec Pages: 6
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
Curtis 1POLXP1000RP Installation & Owner'S Manual preview
1POLXP1000RP
Brand: Curtis Pages: 6
Skoda Fabia Combi 5J Fitting Instructions preview
Fabia Combi 5J
Brand: Skoda Pages: 2
Bilstein E4-WM5-Y479A00 Mounting Instruction preview
E4-WM5-Y479A00
Brand: Bilstein Pages: 7
Roadmaster Even Brake 9400 Owner'S Manual preview
Even Brake 9400
Brand: Roadmaster Pages: 20
APS iArmor IA-S159 Installation Instructions preview
iArmor IA-S159
Brand: APS Pages: 4
Rola RCLSH Fitting Instructions preview
RCLSH
Brand: Rola Pages: 2

Brands by name

Popular brands

Load more brands