Festo CMMO-ST-C5-1-LKP Original Instructions Manual Download Page 149

Page: 149 / 183

B Reference

paramete

Festo – GDCP-CMMO-ST-LK-C-HP-EN – 2017-05b – English

149

PNU 1075

Current string current (Actual Phase Current)

Subindex 1 … 3

Class: Array

Data type: int32

FW …

Access: ro

Reading of the latest current flows [mA] in the individual motor strings.

Subindex 1

Current string current 1 (Actual Phase Current 1)

Latest current of the 1st motor string.

Subindex 2

Current string current 2 (Actual Phase Current 2)

Latest current of the 2nd motor string.

Subindex 3

Current string current 3 (Actual Phase Current 3)

Latest current of the 3rd motor string.

Tab. B.158 PNU 1075

Overwriting of PNU 1080 (basic factor or weight-dependent factor) can lead to higher

motor currents, which can result in oversteering during accelerations in the torque pilot

control. Greater loads are hereby applied to the drive.

The factors are calculated from the parameters (motor, gear unit, feed constant, ...) of the

Festo Configuration Tools (FCT) and written to PNU 1080 and should not be changed.

PNU 1080

Torque pilot control (Torque Feed Forward Control)

Subindex 1

Class: Var

Data type: uint16

FW …

Access: rw1

Reading or parameterisation of the torque pilot control proportion [‰] in the positioning and speed

direct mode.

– 0 = inactive

– 1000 = fully active

The torque pilot control is added to the current controller setpoint value. The value is calculated from

the acceleration.

Tab. B.159 PNU 1080

Summary of Contents for CMMO-ST-C5-1-LKP
























































































































































































Search results

Summary of Contents for CMMO-ST-C5-1-LKP

Reviews:

Related manuals for CMMO-ST-C5-1-LKP

Brands by name

Popular brands

Festo CMMO-ST-C5-1-LKP, Original Instructions Manual

Search results

Summary of Contents for CMMO-ST-C5-1-LKP

Reviews:

Related manuals for CMMO-ST-C5-1-LKP

Brands by name

Popular brands