background image

Section 8 - LCD Keypad Programming Questions

8–53

You must use the left loop on a 2-point module before you can use the right loop. If you have not
used the left loop, then the right loop can not be enabled..

Zone Bypass Enable

148 EN BYP  Zxxx
YES

Indicates whether this zone is bypassable. Zone bypassing can be performed by an
authorized user from the keypad or from a remote programming device. Bypasses can be
performed whether the system is armed or disarmed by an authorized user. Press the 0 key
to toggle between the available choices.

This location should be programmed "NO" for fire zones.

Auto Bypass Option

149 AUTO BY Zxxx
NO

The auto bypass mode allows the zone to be automatically bypassed when the system is
armed in the AWAY mode and the entry zone has not been violated. This option allows
selected zones to be automatically bypassed without having to manually bypass the zone.
This option could be used for interior zones to have selected zones bypassed while remaining
in the location. Press the 0 key to toggle between the available choices.

This location should be programmed "NO" for fire zones.

Arm Faulted

150 ARM FLT Zxxx
NO

This option allows the system to be armed even if the zone is not ready. For example, if the
front door is open normally the user would be unable to arm the system because the system
is not ready. If this option is selected for the front door, then the system can be armed while
the zone is violated, however the door must be returned to normal status by the end of the
exit time period. This option can be selected for Exit/Entry or Interior EE follower zones only.
The zone must restore to normal after the exit time. Press the 0 key to toggle through the
available choices.

Force Arm Faulted

151 EN VENT Zxxx
NO

This option will allow the system to be armed even if this zone is faulted. If selected, the
system will be armed and the zone will be bypassed. Effectively this option will perform a
forced arming of the system without the need to enter the forced arming commands.

Summary of Contents for XL-4





































































































Reviews: