Fanvil X7 User Manual Download

Page: 162 / 162

151

system image has been damaged. Please contact location

technical support to help you restore the phone system.

Device could not register to a

service provider

1. Please check if device is well connected to the network. The

network Ethernet cable should be connected to the

[Network] port NOT the

[PC] port. If the cable is not well

connected to the network icon

[WAN disconnected] will be

flashing in the middle of the screen.

2. Please check if the device has an IP address. Check the system

information, if the IP displays

“

Negotiating

…”

, the device does not

have an IP address. Please check if the network configurations is

correct.

3. If network connection is fine, please check again your line

configurations. If all configurations are correct, please kindly

contact your service provider to get support, or follow the

instructions in “

13.5 Network Packet Capture

” to get the network

packet capture of registration process and send it to Fanvil

support to analyze the issue.

No Audio or Poor Audio in

Handset

1. Please check if Handset is connected to the correct Handset (

)

port NOT Headphone (

) port.

2. The network bandwidth and delay may be not suitable for audio

call at the moment.

Poor Audio or Low Volume in

Headphone

1. There are two Headphone wire sequence in the market. Please

use the Headphone provided by Fanvil, or consult Fanvil the wire

sequence if you wish to use a third-party headphone.

2. The network bandwidth and delay may be not suitable for audio

call at the moment.

Audio is chopping at far-end

in Hands-free speaker mode

This is usually due to loud volume feedback from speaker to

microphone. Please lower down the speaker volume a little bit, the

chopping will be gone.

Summary of Contents for X7



































































































































































Search results

Summary of Contents for X7

Reviews:

Related manuals for X7

Brands by name

Popular brands

Fanvil X7, User Manual

Search results

Summary of Contents for X7

Reviews:

Related manuals for X7

Brands by name

Popular brands