Fanvil X7 User Manual Download Page 113

Page: 113 / 162

102

10.7.2.2

QoS & VLAN

LLDP

Link Layer Discovery Protocol. LLDP

a vendor independent link layer protocol used by

network devices for advertising their identity, capabilities to neighbors on a LAN

segment.

Phone could use LLDP to find the VLAN switch or other VLAN devices and use LLDP

learn feature to apply the VLAN ID from VLAN switch to phone its self.

CDP

Cisco Discovery Protocol. CDP is a not-for-profit charity that runs the global disclosure

system for investors, companies, cities, states and regions to manage their

environmental impacts. According to the CDP, Cisco devices could share the OS version,

IP address, hardware version and so on.

Table 16 - QoS & VLAN

Parameters

Description

LLDP setting

Report

Enable LLDP

Interval

LLDP requests interval time

Learning

apply the learned

VLAN

ID to the phone

configuration

QoS

QoS Mode

configure SIP DSCP and audio DSCP

WAN

VLAN

WAN

VLAN

WAN port

VLAN

configuration

LAN

VLAN

LAN

VLAN

LAN port

VLAN

configuration

CDP

CDP

CDP enable/disable

CDP interval time

Note

QoS & VLAN details refer to

http://www.fanvil.com/Uploads/Temp/download/20180920/5ba383b56c3ef.pdf

Summary of Contents for X7



































































































































































Search results

Summary of Contents for X7

Reviews:

Fanvil X7, User Manual, Page: 113 / 162

Search results

Summary of Contents for X7

Reviews: