Fanvil X7 User Manual Download

Page: 10 / 162

Picture 113 - SIP address and account information .......................................................................... 98

Picture 114 - Configure Advanced Line Options ........................................................................... 98

Picture 115 - Network mode Settings ............................................................................................... 99

Picture 116 - DHCP network mode ................................................................................................ 100

Picture 117 - PPPoE network mode ............................................................................................... 100

Picture 118 - Static IP network mode ............................................................................................. 101

Picture 119 - IPv6 Static IP network mode ..................................................................................... 101

Picture 120 - The phone configures the web server type ................................................................ 104

Picture 121 - Menu password and Settings .................................................................................... 105

Picture 122 - Keypad lock password .............................................................................................. 105

Picture 123 - Set the keypad lock password ................................................................................. 106

Picture 124 - Phone keypad lock password input interface ............................................................ 106

Picture 125 - Web keyboard lock password Settings ...................................................................... 107

Picture 126 - Page auto provision Settings ..................................................................................... 107

Picture 127 - Phone auto provision settings ................................................................................... 108

Picture 128 - Web page firmware upgrade ..................................................................................... 110

Picture 129 - Firmware upgrade information display ..................................................................... 111

Picture 130 - Firmware upgrade ..................................................................................................... 112

Picture 131 - Reset to default ......................................................................................................... 113

Picture 132 - Service Port Settings ................................................................................................. 116

Picture 133 - Dial plan settings ...................................................................................................... 123

Picture 134 - Custom setting of dial - up rules ............................................................................... 124

Picture 135 - Dial rules table (1) .................................................................................................... 126

Picture 136 - Dial rules table (2) .................................................................................................... 126

Picture 137 - Tone settings on the web ........................................................................................... 136

Picture 138 - Web cloud phone book Settings ................................................................................ 138

Picture 139 - IP Camera List .......................................................................................................... 143

Picture 140 - Web Filter settings .................................................................................................... 143

Picture 141 - Web Filter Table ........................................................................................................ 143

Picture 142 - Certificate of settings ................................................................................................ 144

Picture 143 - Device certificate setting .......................................................................................... 145

Picture 144 - Network firewall Settings ......................................................................................... 145

Picture 145 - Firewall Input rule table ............................................................................................ 146

Picture 146 - Delete firewall rules .................................................................................................. 147

Picture 147 - Screenshot ................................................................................................................. 149

Picture 148 - Web capture .............................................................................................................. 150

Summary of Contents for X7



































































































































































Search results

Summary of Contents for X7

Reviews:

Related manuals for X7

Brands by name

Popular brands

Fanvil X7, User Manual

Search results

Summary of Contents for X7

Reviews:

Related manuals for X7

Brands by name

Popular brands