FAAC B680H, Instruction Manual

Page: 30 / 166

2
ENGLISH
CE DECLARATION OF CONFORMITY FOR MACHINES
(DIRECTIVE 2006/42/EC)
Manufacturer:
FAAC S.p.A.
Address:
Via Calari 10 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that:
The operator mod. B680H with control board E680
• is built to be integrated into a machine or to be assembled with other machinery to create a machine under
the provisions of Directive 2006/42/EC;
• conforms to the essential safety requirements of the following EEC directives:
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility Directive
and also declares that it is prohibited to put into service the machinery until the machine in which it will be
integrated or of which it will become a component has been identified and declared as conforming to the
conditions of Directive Directive 2006/42/EC.
Bologna, 1 October 2011
The Managing Director
A. Marcellan
WARNINGS FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS
1) ATTENTION! To ensure the safety of people, it is important that you
read all the following instructions. Incorrect installation or incorrect
use of the product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product..
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of
children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this do
-
cumentation. Any other use, not expressly indicated here, could compromise
the good condition/operation of the product and/or be a source of danger.
6) FAAC declines all liability caused by improper use or use other than that for
which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence of
inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN 12604
and EN 12605. For non-EU countries, to obtain an adequate level of safety,
the Standards mentioned above must be observed, in addition to national
legal regulations..
9) FAAC is not responsible for failure to observe Good Technique in the con -
struction of the closing elements to be motorised, or for any deformation that
may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445. For
non-EU countries, to obtain an adequate level of safety, the Standards men -
tioned above must be observed, in addition to national legal regulations..
11) Before attempting any work on the system, cut out electrical power.
12) The mains power supply of the automated system must be fitted with an
all-pole switch with contact opening distance of 3mm or greater. Use of a
6A thermal breaker with all-pole circuit break is recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream
of the system.
14) Make sure that the earthing system is perfectly constructed, and connect
metal parts of the closing elements to it.
15) The automated system features a built-in anti-crushing safety device consisting
of a torque control. It is however necessary to check its tripping threshold,
as provided for in the Standards described in point 10.
16) The safety devices (EN 12978 standard) protect any danger areas against
mechanical movement Risks, such as crushing, dragging, and shearing.
17) For each system, we recommend using at least one signal light (e.g.: FAA -
CLED or integrated flashing traffic light) as well as a warning sign securely
fixed to the structure, together with the devices described in point “16”.
18) FAAC declines all liability as concerns safety and efficient operation of the
automated system, if system components not produced by FAAC are used.
19) For maintenance, strictly use original parts by FAAC.
20) Do not in any way modify the components of the automated system
21) The installer shall supply all information concerning manual operation of the
system in case of an emergency, and shall hand over to the User the leaflet
supplied with the product.
22) Do not allow children or adults to stay near the product while it is operating.
23) Keep radio controls or other pulse generators away from children, to prevent
the automated system from being activated involuntarily.
24) Transiting is permitted only when the automated system is stationary.
25) The User must not attempt any kind of repair or direct action whatever and
contact qualified personnel only.
26) Maintenance: check at least every 6 months the efficiency of the system,
particularly the efficiency of the safety devices (including, where foreseen,
the operator thrust force) and of the release devices .
27) Anything not expressly specified in these instructions is not permitted.