EtherWAN EX24000 User Manual Download Page 27

Page: 27 / 239

Interface Configuration Mode

Interface

mode

the

EX24000

Switch

used

configure

the

Ethernet

ports

and

VLAN

information.

Valid

interfaces

are:



fe<port

‐

100mb

ports

use

followed

the

port

number.

Example:

fe1



<port

‐

Gigabit

ports

use

followed

the

port

number.

Example:

ge1



vlan1.<vlan#>

‐

VLAN’s

use

vlan.

Followed

the

VLAN

ID.

Example:

vlan1.10

Example 1 configures 100mb port 1

switch_a>

enable

switch_a#

configure terminal

switch_a(config)#

interface fe1

switch_a(config-if)

Example 2 configures VLAN ID 9

switch_a>

enable

switch_a#

configure terminal

switch_a(config)#

interface vlan1.9

switch_a(config-if)

VLAN Database Configuration Mode

VLAN Database Configuration Mode

the

EX24000

Switch

used

configure

the

VLAN

settings.

Example:

switch_a>

enable

switch_a#

configure terminal

switch_a(config)#

vlan database

switch_a(config-vlan)#

Saving a Configuration from the CLI

Example:

switch_a>

enable

switch_a#

write memory

Building configuration.....
[OK]
switch_a#>

EX24000 Switch Users Guide

Summary of Contents for EX24000
















































































































































































































































Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands

EtherWAN EX24000, User Manual

Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands