manualshive.com logo in svg

EtherWAN EX24000, User Manual

The EtherWAN EX24000 is a cutting-edge networking device designed for seamless data transmission. To harness its full potential, make sure to refer to our comprehensive User Manual. Easily accessible for download from our website, our manual grants you free access to all the crucial information you need to optimize your network experience.

Share
Download
background image

 

 

Port Mirroring 

Port mirroring allows network traffic from one port to be copied or mirrored to another port. 
This is a very useful troubleshooting feature in that all data from one port is sent to another 
port which is attached to a computer or other network device that is configured to capture 
packets. This enables a network administrator or technician to see the traffic that is entering 
or leaving a particular port without disrupting normal network operations on the port that is 
being mirrored. 

 

To navigate to the 

Port Mirroring

 menu: 

1.  Click on the 

+

 next to 

Switching

. 

2. Click on

 Port Mirroring.

 

 

To configure port mirroring for a port or ports on the EX24000 switch (see 

Figure 31

): 

1.  Select the port or ports that traffic is to be mirrored from under the 

Mirror From 

column. 

2.  Select the destination port under the 

Mirror To

 drop down box. 

3.  Select the type of traffic that should be mirrored from the 

Mirror Mode

 drop down 

box. The available options are: 

a.  TX – transmit only 

b.  RX – Receive Only 

c.  TX/RX – Transmit and Receive. 

4.  Click on the 

Submit

 button.  

71 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Related manuals for EX24000

i3 International S244 Quick Start Manual preview
S244
Brand: i3 International Pages: 2
H3C S9500E Series Manual preview
S9500E Series
Brand: H3C Pages: 38
H3C S9500E Series Interface Configuration Manual preview
S9500E Series
Brand: H3C Pages: 36
H3C S9500E Series Quick Start Manual preview
S9500E Series
Brand: H3C Pages: 9
H3C S9500E Series Command Reference Manual preview
S9500E Series
Brand: H3C Pages: 36
H3C S12500X-AF Series Configuration Examples preview
S12500X-AF Series
Brand: H3C Pages: 21
H3C S12500X-AF Series Quick Start Manual preview
S12500X-AF Series
Brand: H3C Pages: 42
H3C H3C S7500E-X Configuration Examples preview
H3C S7500E-X
Brand: H3C Pages: 16
H-Tronic TS 1000 Manual preview
TS 1000
Brand: H-Tronic Pages: 32
WAGO ETHERNET Accessories 852 852-0111 Mounting, Installation And Handling Manual preview
ETHERNET Accessories 852 852-0111
Brand: WAGO Pages: 38
Zamel Ledix WDN-01 Quick Manual preview
Ledix WDN-01
Brand: Zamel Pages: 2
GHIELMETTI 674.115.420.30 Operation Manual preview
674.115.420.30
Brand: GHIELMETTI Pages: 12
Silent Gliss 0913 Installation, Programming And Operation Instructions preview
0913
Brand: Silent Gliss Pages: 4
H3C DA-06D12 User Manual preview
DA-06D12
Brand: H3C Pages: 10
Leonton ET2-0602-M Series User Manual preview
ET2-0602-M Series
Brand: Leonton Pages: 17
Gefen 2X2 VGA SWITCHER User Manual preview
2X2 VGA SWITCHER
Brand: Gefen Pages: 12
Woxcon MUH44A-H2 User Manual preview
MUH44A-H2
Brand: Woxcon Pages: 42
QCT QuantaMesh T4000 Series Installation Manual preview
QuantaMesh T4000 Series
Brand: QCT Pages: 41

Brands by name

Popular brands

Load more brands