manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 151

 

Global Configuration Page 

Web GUI Interface 

To navigate to the 

QoS Global Configuration 

page (see 

如下

): 

1.  Click on the 

+

 next to 

QoS

. 

2. Click on 

Global Configuration

. 

 

 

Figure 75: Global Configuration 

 

To Enable the QoS settings: 

1.  Enable QoS, by selecting the drop-down box to the right of the QoS option.  

2.  Choose CoS and/or DSCP next to the Trust option. 

3.  Select the desired option next to Policy: 

a. 

Strict Priority (Queue0-3)

 – Packets must be emptied from the queues in 

order. Starting with queue 3 and ending with queue 0, the packets in each 
queue must be completely emptied before the next queue’s packets are 
considered for transmission. 

b. 

WRR (Queue 0 – 3)

 – each queue is allowed to discharge a certain number 

of packets (according to the WRR weights in the Weighted Round Robin 
section) before moving to the next queue. 

151 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands