EtherWAN EX24000 User Manual Download Page 123

Page: 123 / 239

CLI Command Syntax:

bridge-group 1 instance

<1-15>

Usage Example:

switch_a>

enable

switch_a#

configure terminal

switch_a(config)#

interface fe1

switch_a(config-if)#

bridge-group 1 instance 1

switch_a(config-if)#

switch_a(config)#

switch_a#

STP/RING PAGE - ALPHA RING

Alpha Ring Setting Page

To navigate to the

STP/Ring

-Ring Settings

page:

1. Click on the

next to

STP/Ring

2. Click on

-Ring Setting.

EtherWAN

-Ring Technology

The

-Ring protocol was designed and developed by EtherWAN to overcome traditional

STP and RSTP’s inability to provide fast network recovery and minimize packet loss caused
by link failure. Among the advantages of

-Ring are:



High-speed Recovery

– Less than 15 milliseconds



Flexibility for Network Deployment

– Coexistence with STP, RSTP and MSTP



Ring Coupling

– Smaller rings coupled together to increase network efficiency

Implementing a Simple

-Ring

1. Change the

Ring State

Enabled

2. Click on the

Update Setting

button.

Next, the ports that will be used to connect this switch to the

-Ring need to be assigned to

provide the connection redundancy (see

Figure 58

1. Change

Ring Port 1

to the port you will be using for the first redundant connection

123

EX24000 Switch Users Guide

Summary of Contents for EX24000
















































































































































































































































Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands

EtherWAN EX24000, User Manual

Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands