manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 231

 

  For each port that you wish to apply this application, select the 

Disable

 option from 

the drop-down list under the GMRP Forward All column. 

  Click on the 

Update Setting

 button. 

 

If you wish to transmit all the multicast packets that belong to all the currently registered 
multicast groups on the switch on a port, configure the items listed below: 

  For each port that you wish to apply this application, select the “

Enable

” option from 

the drop-down list under the GMRP column. 

  For each port that you wish to apply this application, select the appropriate option 

from the drop-down list under the GMRP Registration column, according to the 
previous instructions. 

  For each port that you wish to apply this application, select the 

Enable

 option from 

the drop-down list under the GMRP Forward All column.  

  Click on the 

Update Setting

 button. 

 

If you do not want a port to participate in the GMRP protocol, configure the items listed 
below: 

  For each port that you wish to apply this application, select the 

Disable

 option from 

the drop-down list under the GMRP column. 

  Click on the 

Update Setting

 button. 

 

 

231 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands