manualshive.com logo in svg

EtherWAN EX24000, User Manual

The EtherWAN EX24000 is a cutting-edge networking device designed for seamless data transmission. To harness its full potential, make sure to refer to our comprehensive User Manual. Easily accessible for download from our website, our manual grants you free access to all the crucial information you need to optimize your network experience.

Share
Download
background image

 

 

LLDP General Settings 

To navigate to the 

LLDP General Settings 

page: 

1.  Click on the 

+

 next to 

LLDP

. 

2. Click on

 General Settings.

 

 

Enable/Disable LLDP 

To enable LLDP on the EX24000 Switch: 

1.  Select Enable or Disable from the Drop Down box in the 

LLDP

 field of the LLDP 

Transmit Settings box (see 

Figure 91

) 

2.  Click on the 

Update Settings 

button. 

3.  Save the configuration (see the 

Save Configuration Page

) 

 

Holdtime Multiplier 

The Holdtime multiplier for transmit TTL is used to compute the actual time-to-live (TTL) 
value used in an LLDP frame. The TTL value is the length of time the receiving device 
should maintain the information in its MIB. To compute the TTL value, the system multiplies 
the LLDP transmit (TX) interval by the holdtime multiplier. For example, if the LLDP transmit 
(TX) interval is 30 and the holdtime multiplier for TTL is 4, then the value 120 is encoded in 
the TTL field in the LLDP header. 

To adjust the Holdtime multiplier: 

1.  Enter a numeric value between 2 and 10 (default is 4) in the Holdtime Multiplier text 

box. 

2.  Click on the 

Update Settings 

button. 

The TX Interval setting adjusts the time that LLDP information is transmitted by the switch. 
Values can range from 5 to 32768 seconds (default is 30 seconds). 

To adjust the TX Interval setting (see 

Figure 91

): 

1.  Enter a numeric value between 5 and 32768 (default is 30) in the TX Interval text box. 

2.  Click on the 

Update Settings 

button. 

3.  Save the configuration (see the 

Save Configuration Page

) 

179 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Related manuals for EX24000

Cabletron Systems MMAC-Plus 9H423-26 Supplementary Manual preview
MMAC-Plus 9H423-26
Brand: Cabletron Systems Pages: 14
3Com Gigabit Switch 8 Specifications preview
Gigabit Switch 8
Brand: 3Com Pages: 2
DITEC COM500ER Installation Manual preview
COM500ER
Brand: DITEC Pages: 8
Clas Ohlson 36-2824 Quick Start Manual preview
36-2824
Brand: Clas Ohlson Pages: 5
UNICOM SmartGST-2600M Specifications preview
SmartGST-2600M
Brand: UNICOM Pages: 1
XtendLan MATRIX1608A User Manual preview
MATRIX1608A
Brand: XtendLan Pages: 24
I-Tech JKP115-801e User Manual preview
JKP115-801e
Brand: I-Tech Pages: 39
Flowserve PMV WM Ultraswitch User Instructions preview
PMV WM Ultraswitch
Brand: Flowserve Pages: 16
Cabletron Systems MMAC-Plus 9T125-24 Supplementary Manual preview
MMAC-Plus 9T125-24
Brand: Cabletron Systems Pages: 36
Jerguson SAS-16 Installation, Operation & Maintenance Instructions preview
SAS-16
Brand: Jerguson Pages: 4
Articona 386428 Quick Installation Manual preview
386428
Brand: Articona Pages: 2
Velleman VAS4 User Manual preview
VAS4
Brand: Velleman Pages: 8
pro bel VISTEK V1693 User Manual preview
VISTEK V1693
Brand: pro bel Pages: 12
Lindy 32251 and use Installation And Use Manual preview
32251 and use
Brand: Lindy Pages: 54
Opengear IP-KVM 1001 User Manual preview
IP-KVM 1001
Brand: Opengear Pages: 109
Xantech HDMI3X1 User Manual preview
HDMI3X1
Brand: Xantech Pages: 5
Gefen HDMI-341 User Manual preview
HDMI-341
Brand: Gefen Pages: 12
CTC Union ITP-800-8PH24 Quick Installation Manual preview
ITP-800-8PH24
Brand: CTC Union Pages: 14

Brands by name

Popular brands

Load more brands