manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 148

 

Configuring the VLAN Egress (outgoing) Member Ports 

To navigate to the 

802.1Q VLAN Setting 

page: 

1.  Click on the 

+

 next to 

VLAN

. 

2. Click on 

802.1Q VLAN Setting.

 

To configure the egress member ports for each VLAN: 

1.  Click on the VLAN link that you want to configure (see 

如下

). 

 

Figure 72: VLAN Links

 

2.  Check the check box next to the port number that should be the egress member port 

for this VLAN 

3.  Click on the 

Submit

 button (see 

Figure 73

).  

Note

: If an egress member port for a VLAN has the PVID set on that port to be the 

same as the VLAN, then that port will automatically be configured as an egress 
member port for the VLAN by the switch. If a check box is not checked and is 
grayed out, it is because that port is an Access Port with the PVID set to be a 
different VLAN than the current VLAN. 

 

148 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands