EtherWAN EX24000 User Manual Download Page 234 | Manualshive

Page: 234 / 239

background image

DHCP Server

DHCP is a TCP/IP application protocol that allows any TCP/IP device to dynamically obtain
its initial TCP/IP configurations through the TCP/IP protocol itself (in this case, through the
UDP protocol). It is based on the client-server paradigm. The EtherWAN switch can be setup
as a DHCP server to allow any DHCP client to dynamically obtain its IP address, default
router, and DNS servers.

General Overview

The EtherWAN switch can function as a DHCP server for a single VLAN (it can be any
VLAN) on the switch. When functioning as a DHCP server, the EtherWAN switch can be
configured with a range of IP addresses, default gateway and DNS servers, which will allow
the switch to use the dynamic configuration function of the DHCP protocol to provide any
TCP/IP device that is a DHCP client, to dynamically obtain an IP address, default router, and
DNS servers. The EtherWAN DHCP server can also be configured with a lease period that
the DHCP clients are allowed the use of their assigned IP address. In this simple
implementation, both the DHCP Client and the DHCP Server must be on the same network
(same VLAN).

Configuring the DHCP Server

To navigate to the

DHCP Server

page:

1. Click on the

+

next to

Other Protocols

2. Click on

DHCP Server

)

You can use the GUI to set the following DHCP server parameters:



DHCP

Server

Enable



DHCP

VLAN.



DHCP

Client

Parameters

o

IP Address range

o

Subnet

Mask

o

Default

gateway

o

Primary and Secondary DNS.



DHCP Client lease time

234

EX24000 Switch Users Guide

«
...
232
233
234
235
236
...
»

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Related manuals for EX24000

Brand: Quick Pages: 28

Brand: IDEC Pages: 5

Brand: IDEC Pages: 7

Brand: Grizzly Pages: 2

TradeSwitch2-USB

Brand: G&D Pages: 88

TEG-S50TXE SHEETS

Brand: TRENDnet Pages: 20

JTECH-4KPIP0401

Brand: J-Tech Digital Pages: 10

Brand: Sven Pages: 4

Brand: Eagle Pages: 2

Brand: PowerShield Pages: 2

Brand: HighSecLabs Pages: 10

Brand: Allen-Bradley Pages: 4

Brand: Zigen Pages: 18

Brand: LogiLink Pages: 3

stiro RWS-211D/N

Brand: Zamel Pages: 11

Brand: Foxtel Pages: 9

Brand: Belkin Pages: 43

AMX DVX-2265-4K

Brand: Harman Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands