EtherWAN EX24000 User Manual Download Page 28

Page: 28 / 239

SYSTEM MENU

System Information

The System information link on the Left menu of the Web Configuration page takes you to a
page that shows the following (see

Figure 6



System Name

The System name is typically used by network administrators. If SNMP is

enabled on the switch, the system name can be found using MIB II (RFC1213)
in the sysName property.



Firmware Version

If SNMP is enabled on the switch, the Firmware version can be found using

MIB II in the sysDesc property



System Time

System time can be change using NTP



MAC Address

The hardware (MAC) address of the Management interface



Default Gateway

The IP address of your networks Gateway (Typically a Router on your

network)



DNS Server

The Dynamic Name Server (DNS) for your network



VLAN ID

One or more listings depending on the number o VLANs defined on the

switch

Lists VLAN ID, IP address, and subnet mask of the VLAN Interface(s)



Current User Information

EX24000 Switch Users Guide

Summary of Contents for EX24000
















































































































































































































































Search results

Summary of Contents for EX24000

Reviews:

Brands by name

Popular brands

EtherWAN EX24000, User Manual

Search results

Summary of Contents for EX24000

Reviews:

Brands by name

Popular brands