manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 203

 

  The switch will also transmit IGMP Queries to the specified VLAN and 

according to the specified IGMP Query parameters.

 

Enabling the IGMP Snooping Modes 

To navigate to the 

IGMP Snooping 

page: 

1.  Click on the 

+

 next to 

Other Protocols

. 

2. Click on 

IGMP Snooping

. 

To put the IGMP Snooping feature in the correct Mode, follow the steps below: 

  Choose the appropriate choice from the dropdown list next to 

IGMP mode

 

  Click on the 

Update Setting

 button (See 

如下

) 

 

 

Figure 99: IGMP Mode

 

 

Configuring IGMP Snooping General properties 

To navigate to the 

IGMP Snooping 

page: 

1.  Click on the 

+

 next to 

Other Protocols

. 

2. Click on 

IGMP Snooping

. 

To configure the general features for IGMP Snooping in either the 

Passive

 or 

Querier

 mode, 

follow the steps below (see 

Figure 100

): 

203 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands