manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 30

 

System Name/Password 

The System name is typically used by network administrators to make it easier to document 
a networks infrastructure and locate equipment on large networks. If SNMP is enabled on 
the switch, the system name can be found using MIB II (RFC1213) in the sysName property. 
To change the system name: 

1.  Click on the 

+

 next to 

System

. 

2. Click on 

System Name/Password

 (see 

Figure 7

). 

3.  Use your mouse to place the cursor in the 

System Name

 text box. 

4.  Replace the existing name with the name you want to assign to the switch. 

5.  Click on the 

Update Setting

 button. 

By default there is no password assigned to the switch. To add or change a password: 

1.  Click on the 

+

 next to 

System

. 

2. Click on 

System Name/Password

 (see 

Figure 7

). 

3.  Use your mouse to place the cursor in the 

Password

 text box. 

4.  Enter the new password. 

5.  Retype the password in the 

Retype Password

 text box. 

6.  Click on the 

Update Setting

 button below the 

Retype Password

 text box. 

 

Figure 7: System Name/Password 

30 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands