Epson S1D13704 Technical Manual Download Page 263 | Manualshive

Page: 263 / 420

background image

EPSON Research and Development

Page 7

Vancouver Design Center

Interfacing to the Toshiba MIPS TX3912 Processor

S1D13704

Issue Date: 01/02/12

X26A-G-004-02

1 Introduction

This application note describes the hardware and software environment required to provide an
interface between the S1D13704 Embedded Memory Color Graphics LCD Controller and the
Toshiba MIPS TX3912 Processor.

For further information on the S1D13704, refer to the S1D13704 Hardware Functional Specifi-
cation, document number X26A-A-001-xx.

For further information on the TX3912, contact Toshiba or refer to the Toshiba website under
semiconductors at http://www.toshiba.com/taec/nonflash/indexproducts.html.

For further information on the ITE IT8368E, refer to the IT8368E PC Card / GPIO Buffer Chip
Specification.

1.1 General Description

The Toshiba MIPS TX3912 processor supports up to two PC Card (PCMCIA) slots. It is through
this host bus interface that the S1D13704 connects to the TX3912 processor.

The S1D13704 can be successfully interfaced using one of two configurations:

• Direct connection to TX3912 (see Section 2, “Direct Connection to the Toshiba TX3912” on

• System design using one ITE IT8368E PC Card/GPIO buffer chip (see Section 3, “System

Design Using the ITE IT8368E PC Card Buffer” on page 10).

*

«
...
261
262
263
264
265
...
»

Summary of Contents for S1D13704





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1D13704

Brand: Salda Pages: 16

Brand: Veer Pages: 2

Brand: Jabra Pages: 18

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

Brand: Eaton Pages: 10

Brand: Idemia Pages: 29

Brand: LOGICDATA Pages: 23

Brand: WABCO Pages: 3

Brand: HANYOUNG NUX Pages: 4

Brand: HBM Pages: 88

Brand: ARI-Armaturen Pages: 17

Brand: Combi Pages: 20

Brand: Hasco Pages: 78

Brand: Velux Pages: 20

Metso T2 Series

Brand: Neles Pages: 16

LightSYS RP432EV

Brand: Risco Pages: 2

Brand: Greenheck Pages: 32

Brand: ETI Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands