Epson LQ-1150 II User Manual Download Page 125

Page: 125 / 129

Index

Numerics

0 slash, 2-6

A.G.M. (Alternate Graphic Mode), 2-8
Adjusting

paper-thickness lever, 2-28 to 2 -29
tear-off position, 2-25 to 2-26
top-of-form position, 2-22 to 2 -24

Auto CR (carriage return), 2-8
Auto I/F (interface) wait time, 2-7
Auto line feed, 2-5
Auto tear-off, 2-5

Baud rate, 2-7
Bidirectional (Bi-d) printing.

See

direction

Built-in font

list, A-6
selecting, 2-2, 2 -8

Buttons.

See

Control panel

Buzzer (beeper) setting, 2-9

Character table

list, A-7
setting, 2-8

Cleaning the printer, A-2
Contacting EPSON, A-18
Continuous paper

printing, 2-10 to 2-26

Control panel, 2-2 to 2 -10, 4-2
Customer support, A-18
Cut-sheet feeder, 2-33 to 2-37

Data length, 2-7
Default settings

changing, 2-9 to 2-10
option list, 2-3 to 2-4

Driver.

See

Printer driver

Emulation.

See

IBM PPDS emulation

ENERGY STAR Compliance, 4
Envelopes

printing, 2-32

EPSON Status Monitor 3 utility, 1-22,

3-13 to 3-15

Error indication, 4-2 to 4-3
ESC/P 2, A-16 to A-17

Font (default setting), 2-8
Font.

See

Built-in font

High speed draft (default setting), 2-6

I/F (interface) mode, 2-6
IBM PPDS emulation, A-17 to A-18
International character set for Italic

table, 2-8

International character sets, A-7

Labels

printing, 2-30 to 2-31

Lights.

See

Control panel

Summary of Contents for LQ-1150 II


































































































































Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands

Epson LQ-1150 II, User Manual

Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands