Epson LQ-1150 II User Manual Download Page 72

Page: 72 / 129

2-38

Using the Printer

3. Turn on the printer. Hold down the

LF/FF

button to feed paper

in one page.

4. Release the sprocket lock levers of the pull tractor and adjust

the sprocket units to match the width of the paper. Be sure
that the sprocket units on both tractors are aligned so that the
paper is not crooked.

5. Open the sprocket covers. Fit the holes of the paper over the

tractor pins of the sprocket units and adjust the sprocket units
as necessary. (See “Printing on Continuous Paper” on page
2-10.) Close the sprocket covers.

6. If there is slack in the paper between the push and pull

tractors, push in and turn the paper-feed knob on the right
side of the pull tractor to remove the slack.

7. See that the paper is not crooked or wrinkled and lock the

sprocket units in place.

8. Re-install the printer cover and the paper guide.

Summary of Contents for LQ-1150 II


































































































































Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands

Epson LQ-1150 II, User Manual

Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands