Epson LQ-1150 II User Manual Download Page 73

Page: 73 / 129

Using the Printer

2-39

Roll paper holder

The optional roll paper holder (#8310) allows you to use your
printer with 8.5-inch roll paper like that used with telex machines.
This option is not available in all countries.

Follow these steps to install and use the roll paper holder:

1. Turn off the printer and remove the paper guide.

2. Position the roll paper holder beneath the printer as shown

below. Fit the two holes in the base onto the two positioning
pegs on the bottom of the printer.

Caution:

Be careful to avoid dropping the roll paper holder when
lifting the printer. Only the printer’s weight holds it in place.

3. Push the paper-release lever to the single-sheet position.

Summary of Contents for LQ-1150 II


































































































































Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands

Epson LQ-1150 II, User Manual

Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands