Epson LQ-1150 II User Manual Download Page 91

Page: 91 / 129

Using the Printer Software

3-15

Accessing EPSON Status Monitor 3

To access the EPSON Status Monitor 3 utility:

❏

Double-click the printer-shaped shortcut icon on the taskbar.
To add a shortcut icon to the taskbar, go to the Utility menu
and follow the instruction.

❏

Open the Utility menu, then click the

EPSON Status Monitor

icon. To find out how to open the Utility menu, See “Using

the Printer Driver with Windows Me, 98, and 95” on page 3-2
or “Using the Printer Driver with Windows 2000 and NT 4.0”
on page 3-5.

When you access the EPSON Status Monitor 3 utility as described
above, the following printer status window appears.

You can view printer status information in this window.

Summary of Contents for LQ-1150 II


































































































































Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands

Epson LQ-1150 II, User Manual

Search results

Summary of Contents for LQ-1150 II

Reviews:

Related manuals for LQ-1150 II

Brands by name

Popular brands